USB2 HD not recognized by BootIt

User discussion and information resource forum for BootIt Bare Metal.

USB2 HD not recognized by BootIt

Postby nehoc » Wed Nov 21, 2012 6:14 am

I updated my BootIt NG to BM to solve recognition USB2 drives. Unfortunately I have not desired results :
- USB3 drives (2) and USB2 drives with additional interface eSATA (2) are well recognized.
- but USB2 drives (4) are not recognized and I can not change the partitions.(the discs are Western Digital "Elements" (2 2TB and 1TB) and one another 1TB with a USB external interface).

The tests were performed on 2 laptops (ASUS and FUJTSU-SIEMENS) and all USB options in settings were set in BootIt.
Does anyone know the reason for this malfunction?
nehoc
 
Posts: 4
Joined: Tue Nov 13, 2012 7:18 am

Re: USB2 HD not recognized by BootIt

Postby TeraByte Support » Wed Nov 21, 2012 9:30 am

If you're seeing USB3 drives on USB3 controllers then you're probably using
the "BIOS" option which is typically (on the latest computers) only going to
see the one attached at boot. Otherwise, if using the USB bus option, are
you plugging the devices in to the same ports as the others using the same
cable?

"nehoc" wrote in message news:3854@public.bootitbm...

I updated my BootIt NG to BM to solve recognition USB2 drives. Unfortunately
I have not desired results :
- USB3 drives (2) and USB2 drives with additional interface eSATA (2) are
well recognized.
- but USB2 drives (4) are not recognized and I can not change the
partitions.(the discs are Western Digital "Elements" (2 2TB and 1TB) and one
another 1TB with a USB external interface).

The tests were performed on 2 laptops (ASUS and FUJTSU-SIEMENS) and all USB
options in settings were set in BootIt.
Does anyone know the reason for this malfunction?

TeraByte Support
 
Posts: 2310
Joined: Thu May 05, 2011 3:37 pm

Re: USB2 HD not recognized by BootIt

Postby nehoc » Wed Nov 21, 2012 6:57 pm

I tested the USB disks by plugging one at once.
When I set the "USB BUS" option in BootIt settings, the system hangs.
When I connect 3 hard drives on the 3 USB ports of the computer, only those recognized separately are detected.
The result is the same if I plug the disk before powering or when BootIt is running.
nehoc
 
Posts: 4
Joined: Tue Nov 13, 2012 7:18 am

Re: USB2 HD not recognized by BootIt

Postby nehoc » Mon Dec 03, 2012 11:07 am

Hello,
I have not received an answer to my problem. Is it possible that I am the only one in this case? I did the test on three different brands of laptops microcomputers and neither recognizes the USB 2 drive.
nehoc
 
Posts: 4
Joined: Tue Nov 13, 2012 7:18 am

Re: USB2 HD not recognized by BootIt

Postby TeraByte Support(PP) » Mon Dec 03, 2012 9:41 pm

Does the BIOS see those USB drives? For example, do they show up in the boot order or boot menu as valid drives?
Paul Purviance
TeraByte Support
TeraByte Support(PP)
 
Posts: 1099
Joined: Thu Aug 11, 2011 5:51 pm

Re: USB2 HD not recognized by BootIt

Postby nehoc » Thu Dec 06, 2012 5:12 pm

Hello
The bios is "American Megatrends".
On the first page there are the messages :
"Initializing USB Controllers .. Done "
"USB Mass Storage Devices Autodetecting ..
Device # 01 :"

Then from there, the behavior depends on the type of drive connected:

- The self-powered usb disk "Samsung S1 mini" 250 GB is consistently recognized by the bios. The message "01 USB mass storage devices found and configured" is displayed.
- The disk "USB WD Elements" 2TB is not recognized: the microcomputer hangs upon detection remaining on display "Device # 1 :" above.
But if the microcomputer is rebooted with this disk, while it was turned off in the presence of S1 mini, it detects the disk with the same message as the S1. But, after a second reboot, it does not recognize it and hangs.

But in all these cases, BootIt does not detect the disks.
nehoc
 
Posts: 4
Joined: Tue Nov 13, 2012 7:18 am


Return to BootIt Bare Metal