Page 1 of 1

"Unable to read data from file!"

Posted: Sun Mar 29, 2015 12:54 am
by RFSndrs
I just had my Win 7 partition fail and wanted to restore my last image. The image is 6 days old (I do it every Saturday night) and was done with IFW v2.87. I was trying to restore it with BIBM v1.28a. When I ran the restore, it gave me the subject message. I checked ownership in a Win 8.1 partition and permissions were all available to everyone. I then changed ownership to everyone. It still is unable to read the data. What am I doing wrong? Do I need to make an IFW boot disk? Any help would be appreciated.

Bob S

Re: "Unable to read data from file!"

Posted: Sun Mar 29, 2015 2:20 am
by mjnelson99
If you also have IFD, use makedisk.exe to create a bootable device.
Then do the restore from there.
Mary

On 3/28/2015 6:54 PM, RFSndrs wrote:
> I just had my Win 7 partition fail and wanted to restore my
last image. The image is 6 days old (I do it every Saturday night)

and was done with IFW v2.87. I was trying to restore it with BIBM

v1.28a. When I ran the restore, it gave me the subject message.

I checked ownership in a Win 8.1 partition and permissions were all

available to everyone. I then changed ownership to everyone.

It still is unable to read the data. What am I doing wrong?

Do I need to make an IFW boot disk? Any help would be appreciated.
>
> Bob S
>
>

Re: "Unable to read data from file!"

Posted: Sun Mar 29, 2015 3:22 pm
by TeraByte Support
depends on what the problem is - if it's related to the BIOS then use Image
for Linux. IF it's in the file system, you may want to use a TBWinRE or
TBWinPE boot disk then after the store or after copying the files someplace
clean, run chkdsk /f on that drive. If it's on the drive hardware then not
much to do but keep trying, if in cable or port can switch it out.



"RFSndrs" wrote in message news:9463@public.bootitbm...

I just had my Win 7 partition fail and wanted to restore my last image. The
image is 6 days old (I do it every Saturday night) and was done with IFW
v2.87. I was trying to restore it with BIBM v1.28a. When I ran the restore,
it gave me the subject message. I checked ownership in a Win 8.1 partition
and permissions were all available to everyone. I then changed ownership to
everyone. It still is unable to read the data. What am I doing wrong? Do I
need to make an IFW boot disk? Any help would be appreciated.

Bob S


Re: "Unable to read data from file!"

Posted: Sun Mar 29, 2015 5:36 pm
by RFSndrs
I don't know what went on. I read Mary's note and made a bootdisk with IFD and tried that but that gave me the same error message.
Later, after church, I read TB Support's input and before I made an IFL disk, I tried chkdsk /f. (I could boot into safe mode so I did it thru the Win7 OS in safe mode.) Chkdsk went through its iterations and showed no changes that I could read fast enough, but Win7 then booted normally. I thought...hmmmm...but I still have the problem of not being able to restore my image. I then tried to install the win7 image in an unused part of my primary drive and it went along normally. My image is on a secondary 2TB HD and my primary HD is a Samsung 840EVO 1TB drive. MY primary only has several OS's with 500 GB of unused room and that is where I installed the image of Win7.
Everything now seems to be working normally. Can a chkdsk error on my primary SSD cause it not to read my secondary drive? Or...did it fix whatever was wrong with my SSD to allow it to install? BTW, I have more than 4 primaries checked, would chkdsk mess this up?
I don't need a detailed explanation as it is working now.
Bob S

Re: "Unable to read data from file!"

Posted: Sun Mar 29, 2015 9:09 pm
by TeraByte Support
maybe a power cycle helped ?

chkdsk /f is okay with limit primaries disabled or enabled.

"RFSndrs" wrote in message news:9468@public.bootitbm...

I don't know what went on. I read Mary's note and made a bootdisk with IFD
and tried that but that gave me the same error message.
Later, after church, I read TB Support's input and before I made an IFL
disk, I tried chkdsk /f. (I could boot into safe mode so I did it thru the
Win7 OS in safe mode.) Chkdsk went through its iterations and showed no
changes that I could read fast enough, but Win7 then booted normally. I
thought...hmmmm...but I still have the problem of not being able to restore
my image. I then tried to install the win7 image in an unused part of my
primary drive and it went along normally. My image is on a secondary 2TB HD
and my primary HD is a Samsung 840EVO 1TB drive. MY primary only has several
OS's with 500 GB of unused room and that is where I installed the image of
Win7.
Everything now seems to be working normally. Can a chkdsk error on my
primary SSD cause it not to read my secondary drive? Or...did it fix
whatever was wrong with my SSD to allow it to install? BTW, I have more
than 4 primaries checked, would chkdsk mess this up?
I don't need a detailed explanation as it is working now.
Bob S


Re: "Unable to read data from file!"

Posted: Mon Mar 30, 2015 5:53 pm
by RFSndrs
Thanks for chkdsk /f info.
I had power cycled several times trying other things. Still don't know, but it is working yet today.

Bob S