Select Drive Or Partition To Restore???

User discussion and information resource forum for Image products.

Select Drive Or Partition To Restore???

Postby plain » Tue Oct 03, 2017 8:26 pm

I have been trying to restore a partition I had imaged a couple of weeks ago.
IFW 3.06a. Using a PE Disk.

When I get to the screen where it says "Select Where Backup File is Located" I go and find it then click next. The next screen title is "Select Drive or Partition To Restore". ?? The thing is the drive shown is the one I want to restore my original image to. However, this drive (0)only shows one partition instead of 4 and the one partition it does show is of another image from the drive (0). And of course this 'partition' isn't what I want to restore but it is the only choice I have so I click next and now both drives show up (0), and my backup drive where I store my images. Then I select the partition to restore the image to and am told there is not enough room. so I check all the boxes so it will compress the image to fit then hit next and what shows up ready to restore is not the image I first picked but the one in the message box that only shows (0) drive and only one partition. My (0) drive has 4 partitions. I don't remember IFW used to ask me this before I upgraded. Can anyone please help me out? I must have built the PE with the wrong switches but I have no idea what I have done wrong.

Thanks, plain
plain
 
Posts: 22
Joined: Tue Dec 18, 2012 11:33 am

Re: Select Drive Or Partition To Restore???

Postby TeraByte Support » Tue Oct 03, 2017 11:58 pm

The image you choose to restore had one partition backed up to it (you're
still selecting what to restore until it ask for where to restore it). If
you ended up using multi-file on the backup then each partition went to its
own set of image files.

If you were using use simple operations, the backups and restores are always
of the entire drive, the files would be listed and you just pick the one you
want.



"plain" wrote in message news:14235@public.image...

I have been trying to restore a partition I had imaged a couple of weeks
ago.
IFW 3.06a. Using a PE Disk.

When I get to the screen where it says "Select Where Backup File is Located"
I go and find it then click next. The next screen title is "Select Drive or
Partition To Restore". ?? The thing is the drive shown is the one I want
to restore my original image to. However, this drive (0)only shows one
partition instead of 4 and the one partition it does show is of another
image from the drive (0). And of course this 'partition' isn't what I want
to restore but it is the only choice I have so I click next and now both
drives show up (0), and my backup drive where I store my images. Then I
select the partition to restore the image to and am told there is not enough
room. so I check all the boxes so it will compress the image to fit then
hit next and what shows up ready to restore is not the image I first picked
but the one in the message box that only shows (0) drive and only one
partition. My (0) drive has 4 partitions. I don't remember IFW used to ask
me this before I upgraded. Can anyone please help me out? I must have
built the PE with the wrong switches but I have no idea what I have done
wrong.

Thanks, plain

TeraByte Support
 
Posts: 2274
Joined: Thu May 05, 2011 3:37 pm

Re: Select Drive Or Partition To Restore???

Postby plain » Wed Oct 04, 2017 8:02 am

So "Select Partition to Restore" is there to allow you to choose an individual partition out of an image if that image includes more than one partition, right?

Okay so let me ask this then. To help eliminate my confusion. If I restore a single image to more than one partition on the same drive, can I go into BBM and change that partition's name to something else and then IFW will recognize the change? I think I have tried that before but don't remember whether or not it worked. I am still reading and re-reading the manual to try to get my plan down.

Thanks for your patience. I do this so seldom it is like looking at a completely new mountain every time I start climbing.

plain
plain
 
Posts: 22
Joined: Tue Dec 18, 2012 11:33 am

Re: Select Drive Or Partition To Restore???

Postby TeraByte Support(PP) » Wed Oct 04, 2017 10:21 am

plain wrote:
> So "Select Partition to Restore" is there to allow you to choose
> an individual partition out of an image if that image includes more than
> one partition, right?

Correct. Whether or not the image was of the entire disk or not (a partial) you can select an individual partition to restore. In the case of a single partition image you still need to select it (it would be the only one available).

> Okay so let me ask this then. To help eliminate my confusion. If I
> restore a single image to more than one partition on the same drive, can I
> go into BBM and change that partition's name to something else and then IFW
> will recognize the change? I think I have tried that before but don't
> remember whether or not it worked. I am still reading and re-reading the
> manual to try to get my plan down.

You can change the volume label after the restore using BIBM, Windows, etc. You can also change the label of a single partition when it's restored by entering the new name on the options screen. Note that which label is displayed in IFW depends on the setting of the "Use Volume Label" option (volume label vs. EMBR label).
Paul Purviance
TeraByte Support
TeraByte Support(PP)
 
Posts: 1087
Joined: Thu Aug 11, 2011 5:51 pm

Re: Select Drive Or Partition To Restore???

Postby plain » Wed Oct 04, 2017 12:23 pm

Thank You. That helps a lot.
plain
 
Posts: 22
Joined: Tue Dec 18, 2012 11:33 am


Return to Image for DOS/Linux/Windows